Orban Optimod 8200 FM Audioprocessor - GEBRUIKT

Occasions
Orban
Orban Optimod 8200 E3S in zeer goede staat, volledig geserviced, getest en goed werkend. Inclusief nieuwe AES / EBU-kaart
Op aanvraag
  Naar winkelwagen »
  Fout bij toevoegen
Levertijd: Verwacht

Orban Optimod 8200 FM Audioprocessor - GEBRUIKT

Orban Optimod 8200 E3S in zeer goede staat, volledig geserviced, getest en goed werkend. Inclusief nieuwe AES / EBU-kaart 

Met de inmiddels legendarische 8200 klinkt uw FM station zoals de grote radiostations van vroeger.Luid, helder, schoon en aantrekkelijker is voor uw luisteraars. U kunt de meegeleverde fabrieksinstellingen gebruiken of parameters aanpassen om een eigen uniek geluid te creëren. Voordelen van digitale verwerking en bediening zijn onder meer eliminatie van drift van analoge componenten, automatische vooraf ingestelde schakeling voor dagdelen en afstandsbediening via pc-software en modem.

ANALOG AUDIO INPUT
Configuration: Left and right.
Impedance: 600 ohm or 10k ohm load impedance, electronically balanced, jumper-selectable. Common mode rejection: >70dB, 50-60Hz. >45dB, 60Hz-15kHz. Sensitivity: -40dBu to 20dBu to produce 10dB gain reduction at 1kHz. Maximum input level: 27dBu.
Connectors: XLR-type, female, EMI-suppressed. Pin 1 Chassis, Pins 2 and 3 electronically balanced, floating and symmetrical.
ANALOG AUDIO OUTPUT
Configuration: Left and right. Flat or pre-emphasized.
Source Impedance: 30 ohm, /- 5%, electronically balanced and floating.
Load Impedance: 600 ohm or greater, balanced or unbalanced. Termination not required.
Maximum Output Level: 23.7dBu into 600 ohm or greater balanced load.
Connectors: XLR-type, male, EMI-suppressed. Pin 1 Chassis, Pins 2 and 3 electronically balanced, floating and symmetrical.
DIGITAL I/O (Optional)
Configuration: Requires 8200D/32 or 8200D/SRC I/O card.
Input Configuration: Two-channel AES/EBU standard.
Output Configuration:
D/32: Two-channel AES/EBU standard, pre-emphasized to the same pre-emphasis as selected for the processing.
D/SRC: Two-channel AES/EBU standard, software selectable for flat, pre-emphasized to the same pre-emphasis as selected for the processing, J.17 pre-emphasized, or pre-emphasized to the same pre-emphasis as selected for the processing J.17 pre-emphasis.
Input Sampling Rate:
D/32: 32kHz.
D/SRC: 32, 44.1, or 48kHz, automatically selected.
Output Sampling Rate:
D/32: 32kHz.
D/SRC: Software-selectable for 32, 44.1, 32SYNC (frequency locks a 32kHz output to a 48kHz digital input), 48kHz, or SYNC (frequency locks the digital output to the digital input).
Input Level: Adjustable 0 to 20dB attenuation referenced to the maximum allowable digital word.
Output Level:
D/32: Maximum peak output (100% modulation). Fixed @ -2.76dB with reference to the maximum allowable digital word.
D/SRC: Maximum peak output (100% modulation) adjustable 0 to -23dB attenuation with reference to the maximum allowable digital word.
Output Word Length:
D/32:18-bit.
D/SRC: Software selectable 18-bit, or 14-bit truncated with re dithering.
Connectors: XLR-type, female input, male output, EMI-suppressed. Pin 1 Chassis, Pins 2 and 3 transformer balanced and floating.
SCA SUBCARRIER INPUT
Configuration: Subcarrier input sums into composite baseband outputs.
Input Impedance: 600 ohm.
Sensitivity: 1.0Vp-p for 10% modulation of main carrier.
Connector: BNC, floating over chassis ground. EMI-suppressed.
COMPOSITE BASEBAND OUTPUTS
Configuration: 2 outputs, each with independent OUTPUT level control, output amplifier and connector.
Source Impedance: 0 ohm voltage source or 75 ohm, single ended, floating over chassis ground, jumper-selectable.
Load impedance: 37 ohm or greater. Termination not required.
Level: (0 ohm source impedance, 75 ohm or higher load impedance): Adjustable 0-8.0Vp-p with multi-turn OUTPUT LEVEL control.
Connectors: BNC, floating over chassis ground. EMI-suppressed.
Maximum recommended cable length (0 ohm source impedance): 100ft/30m RG-58A/U. Maximum permitted load capacitance 0.047 microfarad.
PILOT REFERENCE OUTPUT
Configuration: Buffered square-wave reference for RDS or other subcarrier services.
Source: HCMOS logic level output, 0-5V peak.
Connector: On Remote Control Interface. DB-25, male EMI-suppressed.
REMOTE COMPUTER INTERFACE
Configuration: RS-232 interfaces to connect to IBM PC-compatible computers, directly or via modem, for remote control and metering.
Minimum Requirements: 386 computer or compatible with hard disk drive, 4MB RAM, VGA grayscale or color display, DOS 3.3, Microsoft(R) Windows(TM) 3.1, and Hayes-compatible modem (2400 baud rate, V.42bis data compression).
Optimum Requirements: Pentium(R) or 486 computer with hard disk drive, 8MB RAM, VGA color display, DOS 5.0 or later, Microsoft(R) Windows(TM) 3.1 or later, and Hayes-compatible modem (9600 baud rate, V.42bis data compression).
Connectors: RS-232 and RS-422; DB-9, male EMI-suppressed.
REMOTE CONTROL INTERFACE
Configuration: Eight (8) opto-isolated inputs. User-programmable to select any eight of: user presets, factory presets, stereo, mono left, mono right, reduction of modulation for SCA 1 ON, reduction of modulation for SCA 2 ON, reduction of modulation for TX1 ON, reduction of modulation for TX2 ON, clock reset, EBS tone, exit test, analog or digital input.
Voltage: 6-24VAC or DC, momentary or continuous, optically isolated. 12VDC provided to facilitate use with contact closure.
Connector: DB-25, male EMI-suppressed.
POWER
Requirements: Switch-selectable on the rear panel, 90-130VAC or 180-260VAC, 50-60Hz; 55VA.
Connector: IEC; detachable 3-wire power cord supplied. AC is EMI-suppressed.
Ground: Circuit ground is independent of chassis ground; can be isolated or connected with a rear panel switch.
Safety standards: IEC65, UL.
DIMENSIONS
19" (48.3cm) wide, 7" (17.8cm) high, 15" (38.1cm) deep. 4 rack units.
ENVIRONMENTAL
Operating Temperature Range: 32-122 degrees F; 0-50 degrees C.
Humidity: 0-95% RH, non-condensing.