Inovonics 525N AM Modulatie Analyzer

Inovonics 525N is een derde generatie AM modulatie monitor van Inovonics. De 525
kan ofwel een directe vanaf de zender meten maar ook nauwkeurige off-air metingen is mogelijk.
3.599,00 Excl. BTW
  Naar winkelwagen »
  Fout bij toevoegen
Levertijd: 7-14 Dagen

Inovonics 525N AM Modulatie Analyzer/ AM Broadcast


The 525N is a third-generation AM Modulation Monitor from Inovonics. It
can accept either a direct feed from the transmitter, or function as a precision Reference Receiver to give accurate off-air measurements reflecting ATU, phasor and antenna parameters.
A proprietary phase-locked synchronous detector provides precise
demodulation, rejects interference, and recovers only the amplitudemodulated component of HD Radio™ ‘hybrid digital’ transmissions. The 525N is also compatible with powersaving
MDCL operation.
Although the 525N maintains full wideband response for measurement,
it features user-selectable audiomonitor cutoff characteristics to
mitigate noise or to simulate the response of consumer radios.
IP connectivity with full SNMP support gives the user total access to the unit
from any computer, tablet or mobile device. Setup, metering, alarms and
audio monitoring are all available from the remote monitoring point.
The 525N is supplied with a largeaperture, weatherproof loop antenna.

Features


  • Accurate, simultaneous display of positive and negative peak modulation with Peak Density histogram 
  • Absolute-limit and user-programmable Peak Flashers 
  • Calibrated RSSI signal strength display and asynchronous noise readout 
  • Alarms for Low Signal, Audio Loss and Overmodulation with panel indicators and ‘tally’ closures 
  • Full Web interface gives total remote control of all setup parameters, metering, alarms with logging, and streamed audio monitoring 
  • ADDITIONAL FEATURES  
  • 5 Station Presets 
  • 10kHz/9kHz channel spacing 
  • Balanced audio output 
  • Supplied with out- door loop antenna 
  • Headphone jack 



Specifications


OFF-AIR RECEIVER


Receiver Topology: Single-conversion superheterodyne; 300kHz IF; phase-locked I/Q synchronous detector.
RF Inputs: The 75-ohm (F) antenna input connects to the supplied broadband loop antenna. Cable is not included, but up to 100 feet of general-purpose RG-6 CATV coax may be used. A short wire antenna may prove adequate in high-signal areas that suffer minimal interference. A 50-ohm (BNC) high-level input accepts a direct RF sample between 1V and 7V r.m.s. / 3V–20V p-p.
Tuning Range: Tunable via the front-panel menu or the Web interface:
520kHz to 1720kHz in 10kHz steps
522kHz to 1719kHz in 9kHz steps Five station-memory pushbutton/Web presets are provided.

MEASUREMENT PARAMETERS


Measurement Bandwidth: Carrier amplitude demodulation extends to 10kHz, ±0.2dB. Measurement is not affected by the user-selectable audio cutoff.
Audio Response: User-selectable “FLAT” response, or restricted in programmable 1kHz steps between 10kHz and 2kHz.
De-Emphasis: A menu command switches-in the NRSC ‘truncated’ 75μs de-emphasis characteristic to the program audio outputs with any restricted audio bandwidth selection.
Audio Distortion: Typically 0.15% THD at 50% carrier modulation; <0.5% at 99% modulation.

DISPLAYS


Modulation Display: The peak-responding front-panel bargraph readout shows positive and negative modulation peaks simultaneously, with extended persistence of the most recent highest peak value. Measurement resolution is 1% between 50% and 100% (negative) and 50% and 140% (positive) modulation, and 2% between 20% and 50% modulation.
RSSI and Noise Display: The Modulation Display may be switched to show the dBuV level of the incoming carrier (RSSI) and a relative measurement of asynchronous noise.
Peak Flashers: • Absolute-limit flashers are factory-calibrated at –100% and 125% carrier modulation. • A second set of flashers may be programmed by the user to values between –70% and –100%, and 70% and 140%.


CONNECTIONS


Program Audio Outputs:
The active-balanced, rear-panel program audio output (XLR) delivers 4dBu from a 200-ohm resistive source.
Front-panel headphone jack (¼-inch, TRS).
Alarms: Open-collector NPN transistor outputs (screw-terminal block) for low signal, program audio loss and overmodulation. Closure polarity is programmable. WEB INTERFACE
Connection: RJ45 jack for remote setup and operation via TCP/IP; DHCP or Static IP with local or remote selection
Remote Monitoring: Remote Web-based monitoring of off-air audio.
Network: Comprehensive network configuration utility including dynamic DNS and full SNMP support with downloadable MIB file.
Alerts: Supports email and text message services with or without SSL

MISCELLANEOUS


Power Requirements: 105–130VAC (0.250A Fuse) 210–255VAC (0.125A Fuse), 50/60Hz; 10W..
Size and Weight: 1¾”H x 19”W x 7”D (1U); 9 lbs. (shipping).
Peak Flashers: Environmental: 0°C – 50°C operating temperature range; 95% non-condensing relative humidity; up to 3000 meters AMSL.
Inovonics 525N Brochure